ASEAN SWITCHGEAR MARKET REPORT SIZE GROWTH

Test Report on the New Long-Distance Optical Transceiver

Test Report on the New Long-Distance Optical Transceiver

TOKYO - August 12, 2025 - NTT has successfully demonstrated long-haul, high-capacity optical transmission at 160 terabits per second over distances exceeding 1,000 km. In this report, we delve into the pursuit of efficient, high-speed data, and long-range transmission, unveiling the state-of-the-art optical transceivers. Huawei commissioned EANTC to validate functional, interoperability, and performance aspects of the Huawei OptiXtrans DC908 wave division multiplex (WDM) solution with a specific focus on the Storage Area Network (SAN) use case scenarios. Reliable optical transceiver performance keeps your network running smoothly and avoids costly interruptions. For example, flaws in wavelength stability, power output, or temperature tolerance can lead to data loss, latency, or hardware.

Read More
Test Report on Energy-Saving DAC High-Speed ​​Cable

Test Report on Energy-Saving DAC High-Speed ​​Cable

This edited past contribution to INMR by Paul Leufkens of Power Projects Leufkens in the United States along with Prof. Edward Gulski and Rogier Jongen at onsite hv solutions in Switzerland, focused on application of DAC for after-laying testing and diagnostics of all types of. IEC standards for power cable systems up to and above 150 kV rated voltage are manufacturer standards and, according to experts, do not necessarily provide adequate recommendations for testing after-installation. The IEEE Guide for Field Testing of Shielded Power Cable Systems Rated 5 kV and Above with Damped Alternating Current (DAC) Voltage, has been available for the past 7 years [3, 16]. Advanced DAC technology utilizes voltage testing in combination with non-destructive diagnostic methods, such as partial discharge (PD) detection and dissipation factor (tan δ) measurement of the cable system and associated accessories.

Read More
Substation cable tray size requirements

Substation cable tray size requirements

Standard cable tray widths per IEC 61537 and manufacturers' ranges are typically 50, 75, 100, 150, 200, 225, 300, 400, 450, 500, 600, 750, 900, and 1000mm. maintain spacing or to keep cables in place when the tray is ect the minimum bend ra-dius for cables as they exit the bottom of the cable tray. A rung spacing of 6 to 9 inches (150 to 230 mm) is preferable when the cable tray cont d for instrumentation and control applications that require. Ladder cable tray is available in widths of 6, 9, 12, 18, 24, 30, 36, 42 and 48 inches with rung spacings of 6, 9, 12 or 18 inches. These dimensions define the available cross-sectional area for cable installation.

Read More
How to calculate the size of the bends in a cable tray

How to calculate the size of the bends in a cable tray

To find the size of the cut in the tray, you divide the distance between the sets by the width of the tray. Follow these simple steps: Define Tray Dimensions: Enter the width and depth of your planned cable tray (in mm or inches). Cable tray sizing is a technique of establishing the right dimensions of a cable tray system with regard to its length, width, and height so that the current and future cable loads can be sufficient. Calculate cable tray offset dimensions, bend section length, and horizontal run for obstacle routing Two Bends Per Offset: Every offset requires two equal bends — one to move laterally and one to return to parallel.

Read More
What size support bracket is used for cable trays according to national standards

What size support bracket is used for cable trays according to national standards

Bridge bracket when the wires in the cable tray are laid vertically, the cable wires should be fixed on the bracket of the bridge tray at an interval of 1. A cable support system consists of cable support lengths and system components, such as cable support fittings, support elements, mounting elements and system acces-sories. The mechanical and electrical characteristics, tests, certifications, overall quality management, recommendations mentioned in this technical guide only apply to our own cable management ranges and cannot under any circumstances be transposed to si osure, overheating or. maintain spacing or to keep cables in place when the tray is ect the minimum bend ra-dius for cables as they exit the bottom of the cable tray. A rung spacing of 6 to 9 inches (150 to 230 mm) is preferable when the cable tray cont d for instrumentation and control applications that require.

Read More

Get In Touch

Connect With Us

📧

Email

[email protected]

📱

Spain Office (HQ)

+34 936 214 587

🇪🇺

EU Technical Center

+49 89 452 38 217

📍

Headquarters (Spain)

Calle de la Tecnología 47, 08840 Viladecans, Barcelona, Spain